A liquid cleaning agent containing phosphoric acid and non-ionic surfactants, designed to remove rust and contaminants from metal surfaces. RustConvert effectively eliminates corrosion and deposits, restores metal shine, and prepares surfaces for painting. The product is suitable for various surfaces, such as metal, wood, tile, and paint, ensuring their cleanliness and readiness for further processing.

Preparation: Clean the surface from dirt and degrease before application.
Solution Preparation: Always add RustConvert to water, not the other way around, using a plastic container.
The exact dosage for cleaning cannot be precisely determined as it depends on the level of contamination and the desired result. The user regulates the consumption of this product. A solution concentration of 10-50% is recommended, depending on the scale and degree of contamination. Note that a 10% solution can be used for daily cleaning of simple contaminants and light rust. Accordingly, a 50% solution is intended for particularly difficult cases – removing deeply ingrained dirt and rust.
Application: RustConvert solution can be applied to the surface manually (with a brush, cloth), by spraying, or by immersing small parts in the solution.
For individual parts, the immersion method in an undiluted product is applicable; after deposits have softened, rinse with water.
Rinsing: After treatment, thoroughly rinse the surface with a stream of clean water under high pressure.

A high-quality hydrophilic emulsifying and dissolving agent, specially developed for cleaning and degassing tanks, cisterns, and containers contaminated with residues of crude oil and petroleum products. The product can be used both concentrated and diluted for cleaning cargo tanks, deep tanks, bilges, and other containers in the petrochemical industry. It is compatible with most coatings and suitable for cleaning methods such as sloshing, mechanical washing, or manual spraying.

Application: A solution with a dosage of 0.5-2%, or 5-20 litres of product per tonne of wash water, is recommended. The mixture is prepared in the tank designated for cleaning. Typically, a wash solution volume equal to 5-10% of the tank's capacity is used.

Dosage and results depend on the level of contamination, the temperature of the cleaning solution, and the number of tanks to be cleaned with the same batch. The best results are achieved by heating the solution to 60-70°C.

TankClean can be sprayed directly onto the tank surface to be cleaned. The product's contact time with the contamination should be at least 30 minutes. Bulkheads and sides can be cleaned using tank washing machines or high-pressure washers. The best results are achieved when washing with hot water at 60-70°C. Washings must be continuously pumped to a slop tank or discharged to shore reception facilities.

A water-based alkaline cleaner designed for operation under heavy soiling conditions. The product has a broad spectrum of action and is effective in removing stubborn contaminants such as fats, wax deposits, vegetable and animal oils, sludge, soot, carbonaceous deposits, and deeply ingrained dirt. TankPur is also applicable for cleaning cargo holds after transporting coal and coke.

Application: Can be used in various cleaning operations, applied with brushes, manual spraying, low- or high-pressure washing machines, etc.

Application Methods & Dosage:

1. Direct injection via tank cleaning machines: Use a dose of 1-20 litres per tonne of wash water (0.1-2%).
2. Recirculation method: Use a dose of 1-20 litres per tonne of wash water (0.1-2%).
3. Spot cleaning: Manually spray the pure product or prepare a 20% solution and leave for 20-30 minutes. Then rinse with water. The surface should remain wet.

Soot removal from Inert Gas Systems:

1. Apply TankPur using a high-pressure washer at a 1:4 ratio with water. However, if cleaning was initiated by manual spraying, apply undiluted TankPur to the surface at a rate of 1 litre per 12 sq. meters.
2. Leave for 30-45 minutes. The surface must remain wet.
3. Rinse with hot water (80°C) and check the result.
4. Repeat if necessary.

Furthermore, TankPur can be used for cleaning tanks after animal, vegetable, and fish fats, petroleum sludge, waxes, and cargo holds after soot, coal, and other bulk cargoes

A biodegradable universal cleaner and degreaser containing wetting agents and alkaline components. This multi-purpose agent effectively removes contamination on vessels, including in living quarters and galleys. Thanks to its environmentally friendly properties and biodegradability, it is ideal for various cleaning tasks on board a vessel.

Preparation: Depending on the application, MultiCleaner is diluted with water in various proportions from 1% to 50% or used in its concentrated form.

Application in Engine Rooms: In engine rooms with heavy contamination, the product is used undiluted. Apply to the surface, allow to penetrate, and then rinse off with hot or cold water or remove using washing machines.

Application in Common Areas: For cleaning common areas such as decks, tiles, walls, and bulkheads, use a solution with a concentration of 1% to 10%. Apply with mops, sprayers, or sponges, then rinse with water.

Application on Objects: For small objects like furniture, plastic, or vinyl, a solution with a concentration of 1–5% is recommended, followed by thorough rinsing.

An alkaline cleaning agent developed for removing heavy contaminants, such as animal and food oils, from tanks with special linings. Its formula is optimized for efficient cleaning, overcoming the limitations associated with traditional alkaline cleaning compositions. The product can also be used as a deodorizing agent in various applications.

Application: For cleaning tanks that have carried food-grade cargoes using the "Rock and Roll" method, add 15-20 litres of FatLine per tonne of fresh or seawater to fill the tank to 30% capacity.
For cleaning via injection or recirculation, prepare a solution with a concentration of 5-10% FatLine mixed with water (fresh or sea). Tanks must be emptied and rinsed with water beforehand. FatLine can be applied undiluted when sprayed, followed by rinsing. The product has high alkalinity – safety precautions must be observed.

A highly concentrated liquid alkaline additive designed for the effective removal of scale and corrosion in steam and hot water boilers. The product is suitable for boilers with pressures above 30 bar and helps maintain equipment cleanliness and efficiency. Its composition includes alkaline components, scale and corrosion inhibitors, as well as volatile amines for condensate system protection and as a sludge conditioner.

Application: To achieve maximum effectiveness, BW-Cleaner should be continuously added to the boiler system using a dosing unit. Alternatively, the agent can be introduced into the boiler feed system via a bypass device.
Avoid contact with aluminium, zinc, and galvanized steel.

Dosage: The initial dosage for an untreated system is 2.4 litres per tonne of boiler water. This improves water treatment to a level of 200 ppm phosphate alkalinity.
If dosing is done manually, the dose is calculated using a special chart.
After a short period of use, the operator will be able to easily determine the required treatment level.

A highly effective dry acidic cleaner designed to remove scale, rust, and other deposits from boilers, diesel cooling systems, condensers, evaporators, air heaters, and heat exchangers. It can be applied to most shipboard systems, making it a universal cleaning solution.

Application: For large systems, solution circulation is recommended; for small components, soaking in a bath is suitable. If contaminated with oil or sludge, perform preliminary cleaning.
The BW-Cleaner solution is prepared with fresh water at a concentration of 2.5% to 10%, depending on the level of scaling. Always add BW-Cleaner to water, not vice versa. Maintain the solution temperature at 60-70°C.
Used solution can be reused (up to two times) by adding 25% of the initial product dose.

Treatment: Do not use the product on aluminium, zinc, tin, or galvanized surfaces. To remove calcium sulphate and stubborn iron oxides, use a more concentrated solution by adding 1 part salt to 20 parts BW-Cleaner.
After cleaning with BW-Cleaner, flush the system with a 0.5% solution of BW-Cleaner in fresh water for 2-4 hours to neutralize the acid.
Before cleaning, remove zinc plates and anodes, as with any acid treatment.
The use of acid may generate combustible gases, including hydrogen. Ensure good ventilation to prevent gas accumulation.

Recommendations:
Do not perform welding work during cleaning.
Do not leave the acid solution in the system for more than 24 hours.
Do not add salt when cleaning stainless steel equipment.

A liquid agent designed to protect the engine cooling system from corrosion and scale formation. It combines effective film-forming corrosion inhibitors and scale-suppressing components. CW-Cleaner dissolves easily in water in any proportion and is chromate-free, providing reliable protection for the cooling system without harmful components. CW-Cleaner is used in all types of engine cooling systems, protecting ferrous metals, copper and copper alloys, as well as all other alloys including aluminium components. It does not damage rubber seals or other non-metallic parts of the cooling system.

Preparation: Before using CW-Cleaner, it is recommended to flush the system to remove old coolant and contaminants.
Dosage: CW-Cleaner is easy to dose and mix with ethylene glycol. The product contains special components that not only protect against corrosion but also prevent scale formation. It is important to monitor the condition of the cooling system. If leaks are detected, immediate action must be taken.
Overdosing CW-Cleaner will not harm the system. Control is performed by simple testing for nitrites and pH.

Application: CW-Cleaner is convenient to use and fully compatible with water in ethylene glycol solutions. This agent contains anti-scale additives that help keep engine cooling systems clean, free from corrosion and scale. CW-Cleaner maintains efficient heat transfer and prolongs engine life.
Instantly check for abnormal coolant losses and take appropriate measures. CW-Cleaner should be introduced during the circulation of the cooling water. CW-Cleaner is best added via a feeder installed on the bypass of the circulation system, or in small systems, it can be added directly to the expansion tank.
Initial treatment is performed at a rate of 32 litres of CW-Cleaner per 1 cubic metre of coolant, providing a level of 700-1000 ppm nitrite (1000-1500 ppm sodium nitrite).

A hydrocarbon-based biodegradable dispersant designed to effectively disperse petroleum products spilled at sea, on vessels, piers, and shipyards. The product is developed for spill response during loading, unloading, and bunkering operations. With high spreading ability and low toxicity, it ensures reliable environmental protection.

Preparation: OilSpill Pro is recommended for use undiluted; the product requires no additional preparation.

At-Sea Spill Response: For spill response at sea, use OilSpill Pro undiluted via manual sprayers, boats with installed equipment, or fire hoses with injectors. After application, allow the product to be absorbed, then vigorously agitate the mixture using fire hoses, propellers, or boards towed behind a work boat. Application is prohibited in areas with depths less than 20m or near zones with special environmental restrictions, such as regulations from local fishery or environmental inspectorates prohibiting the use of such agents.

Beach and Shoreline Spill Response: On beaches and shores contaminated with petroleum products, OilSpill Pro is sprayed in its pure form. Allow time for the product to be absorbed by the oil. After absorption, rinse the contaminated surfaces with water. Product consumption depends on the type, thickness, and condition of the oil layer. On average, 1 litre is sufficient to treat approximately 10 m², but in some cases, reapplication may be necessary.

On-Deck Spill Response: For spills on deck, remove excess oil, spray OilSpill Pro, and allow it to be absorbed. Then, rinse the contaminated areas with high-pressure water. Repeat the procedure if necessary.

A liquid blend of surfactants and emulsifying agents dissolved in a specially inhibited, inorganic acid-based solvent. DiscPur effectively removes stubborn and persistent deposits that accumulate in fuel and oil separators, providing exceptional cleaning efficiency without the need for disassembling the discs.

Application: DiscPur can be used in its pure form or diluted (20% solution with fresh water), depending on the degree of contamination, the availability of heating, and the time available for cleaning.
The higher the concentration, the more effective the cleaning. Cleaning time ranges from 30 minutes to 2 hours, depending on the aforementioned factors.
Faster and more effective cleaning can be achieved by heating to a maximum of 60°C. After ensuring the unit or individual parts are clean, they must be rinsed with fresh water to remove all traces of contamination and DiscPur.

Cleaning Methods:

1. Remove the separator disc stack and soak in a DiscPur solution. Circulation and heating of the solution to 50°C-60°C will enhance cleaning.
2. Remove the separator disc stack, disassemble it, and subsequently soak the discs in DiscPur. Circulation and heating of the solution to 50°C-60°C will enhance cleaning. If a soaking tank is not available, the solution can be applied to the discs using a sprayer.

Do not use galvanized containers as soaking tanks. Cleaning time ranges from one to three hours depending on the level of contamination.
After the cleaning procedure, ensure the unit or parts are clean, then rinse them with fresh water to remove all traces of contamination and the product.

A powerful cleaner and degreaser for cleaning fuel filters, oil coolers, and heaters. The product effectively removes carbon deposits and stubborn contaminants thanks to its high solubility and penetrating ability. Ideal for cleaning metal and ceramic filters, burner nozzles, and other machine parts, restoring their efficiency.

Application: Use in its pure form at a cleaning temperature up to 60°C. The effect is achieved by filling and/or circulating the product. The cleaning process lasts from 8 to 24 hours, depending on the level of contamination.
For the circulation method: ensure circulation for at least 2 hours, then rinse with water. For more effective rinsing, it is advisable to use hot water (up to 60°C).

Limitation: Not to be used for ultrasonic cleaning.

Recommendation: Degreaser Pro is recommended for cleaning using the immersion method.

A universal cleaner specially designed for cleaning and degreasing electrical equipment. It effectively removes oils, greases, and other contaminants from electrical components, machine parts, and ball bearings. The product has a controlled evaporation rate, preventing the formation of emulsions with water and allowing for the separation of oils in an oily water separator. It also cleans internal parts of motors and generators well.

Application: Use ElSol Pro only in well-ventilated areas and in its pure form. It can be applied using a brush, swab, hand tools, or sprayers.
For cleaning small parts, use the immersion method with short-term dipping in a bath of the product. A few minutes are sufficient to remove oil contamination; for stubborn contamination, up to two hours. The bath should be covered with a lid to prevent evaporation and harmful vapors. A water layer to prevent evaporation is not recommended.
After soaking, parts should be blown off with clean compressed air or rinsed with water and then dried. For manual application, contamination is removed using sprayers, and residue is removed by blowing with compressed air.
Plastic and rubber parts may be damaged; they should be removed or tested on a small area before treatment.
After cleaning generators and electric motors, check the insulation resistance.

Limitations: Do not use on operating generators or electric motors. Avoid contact with open flames.